6V backup battery power supply regulator with IC 7805

This simple and cheap 6 volt power supply circuit with 6V backup battery system.
The AC power 220V is entered to through input of transformer-T1 to reduce voltage as 9VAC, then wire connected to four diode D1-D4 as bridge rectifier became to 11VDC, then the current is filtered to dc voltage that low ripple output and then the voltage is regulated to 6VDC constant voltage by IC-KA7805( IC-7805 type) In normal it is used for 5 volt only but now we add two resistor to determined output voltage is 6 volt and passed through diode 1N4002-D6 to output is 6 volt.

Read more source: http://www.eleccircuit.com/6v-backup-battery-power-supply-regulator-with-ic-7805/

DC adjustable power supply high efficiency 0-50V 1A by CA3130-CA3086

Today I would recommend a DC power supply that can adjust voltage and current, another one circuit. It’s very interesting since is highly effective, devices not very. This circuit has special feature that can supply output voltage widely range is during 0.1V to 50V
With value of the load regulation changes not more than 0.005% between 0A to 1A.
-The stability of regulation, when change the input voltage, the criterion is 0.01%.
-The noise output signal under 250uV
-This circuit can provide an output voltage in a wide range by the number of IC-CA3130 by the input range is 0V.
-During the extension of the output voltage can not, by adding Q4 between this IC and transistor both series. This circuit has a high threshold makes the regulation is accurately high level. Darlington transistors T1/T2 and make a high enough flow. Q3 is the limited current output. When the VR1 fully anticlockwise, Q3 current limit around 0.6A. This current limit, it will not work When the VR2 rotate clockwise until it stops.

Read more source : http://www.eleccircuit.com/circuit-power-supply-regulator-01-50v-1a-by-ic-ca3130-ca3086-2n3055/

Small DC to DC converter 1.5V or 3V to 9V by TL496

When you have sized batteries is 1.5V or 3V, but need a voltage 9VDC, DC converter circuit to help you for sure!
Some problems in the electronics job, can modify or bring devices come to apply available not difficult If we know the principles and limitations of those devices. As the project is being offered at this time, will be bringing sized batteries 1.5 volt connected through an electronic circuit called dc converter to increase the voltage to have higher value be 9 volt instead of the battery 6 pack, connected series.
It can also increase the voltage from the battery 3 volt to 9 volt as well be the original circuit, and it will allow more current.
Properties of the IC TL496
- A TL496 be control circuit of the power supply, by the circuit was designed, so that the output voltage is 9 volt. For the change of the input voltage, which comes from the battery 1 or 2 pack. The TL496 operates in a switching regulator, the power loss is less than the typical linear regulator.

Read more source: http://www.eleccircuit.com/micro-dc-converter-3v-to-9v-using-tl496/

DC voltage adjustable power supply 0-50V up to 2A by ua723-2N3055

The Circuit power supply regulator 0-50V 2A by IC LM723 + Transistor 2N3055 & BD140 & A671 is nice Pwer supply,
For all electronic user. You can Current control by VR 5K, LED5 For display OVERLOAD.
To use transformer 3A, Transistor to Hold Heatsink. To adjust the output voltage< VR1 - 5K (VOLT CONTROL)
OUTPUT : 0V to 50V , 2A
Today I would like to introduce you to DC Voltage adjustable regulator voltage between 0V to 50V and current up to 2A. Which are suitable for various electronic circuit, when viewing circuits in the figure, many people will think that, in this circuits outdated, but I think, it is also highly effective are.
The VR2-5K be adjusted voltage output between 0 to 50Volt.
-The VR1- 5K be fined current output load 0 to 2 Amp.
- When the short-circuit current limit or severe, it is a good system.
- Low noise, due to the use IC uA723 dc voltage regulator IC which is high quality, widely used for many years.


Read more at source: http://www.eleccircuit.com/power-supply-regulator-0-50v-2a-by-ic-lm723-transistor-2n3055-bd140-a671/

Power supply regulator 1_2V-20V and 3V-6V-9V-12V 3Amp With LM317T and 2N3055

This is the high quality power supply to provide high current 3A. And still adjust voltage in steps from 3V, 6V, 9V, 12V. adjust voltage is continuous 1.25V to 20V. Using LM317T and 2N3055 are main parts so easy to made and cheap.
Friends would known the power supply as well. Because you must use in various circuit experiment. It originally had a small supply current, when found projects that uses lot of current. Such as an audio amplifier circuit so provide current is not enough.
This project can help you. Because of provide high current 3A. And still adjust voltage in steps from 3V, 6V, 9V, 12V. adjust voltage is continuous. And you do not have to worry. This creates a simple and economical. If interested, please read on.
How it works
In the circuit below can be seen that, when opening switch S1 is current through the transformer. To convert from 220V AC to 18V, then through diode bridge rectifier BD1. But is a DC supply that still not smooth. Then, a filter capacitor C1 serves electricity, out of BD1 to be more smooth with the LED1 to show that power is supplied to already.
When the filter current is smooth on one order. The current will through the regulator circuit that the main components are IC1(LM317T) and Q1(2N3055).
-IC1 is the regulator IC number : LM317T.
-Q1 is power transistor NPN type number : 2N3055.
Read more and view circuits

Power Regulator +12V_-12V by 7812 , 7912

I plan to show you, with an interesting concept.When I was make pre-amplifier circuit is small. I did not plan on the power supply. It requires low supply current is only 100mA. But the need for dual voltage. Or 3 line is +12 V,-12V and Ground. At that time, I have not the least knowledge and a few equipments. The regulator ICs I use IC7812 and IC7912 (hard to bought). I make this circuit. It works great.
notice point
In circuit I use diodes D1, D2, only both because I’d forgotten to add, and this is a low current, using a half-wave diode rectifier enough. and The transformer is 300mA -15V CT 15V that cheap than other sizes.
-IC1-IC2 do not need to hold the heat sinks because the very low currents.
-LED1 is indicator to Power ON that R1 is the current limiter of LED1.
-C1,C2,C3,C4 are first filter that time I has them many so place various 2200uF.
How to built.
This project I put them in peforated board, it easy to use, and so cheap. But at time I put wrong pin capacitor, when entering the power supply, causing it to burst. I was shocked very much.But I do not Discontinued this project.
Read more and view circuits

Top Linear power supply regulator 5V 5A with 7812 and LM723

When you need a power supply often missed the 3 legs Regulator ICs. But some jobs that apply a high current over 1 Ampere up there, is very difficult. Even if it is 5 amp and 10 amp, but the price is quite high.
This project is designed with the concept of the modular regular circuit is using the output. Which is composed of two or more transistors, to current as shown in the circuit. And a control section is not sensitive to noise, which we would have to use IC-723. Although the present may be perhaps was overshadowed with the 3-pin regulator IC. However, with good characteristics, makes us choose to use it for Supply output voltage from 2 to 7 volts.
The voltage for provide IC1-LM723 get from the increasing the voltage and then filtered to smooth. then, through the control the voltage regulator using 3-pin. This method Is good for power transistors, because we make the output voltage and the before into transistor voltage, both difference as little as possible. without prejudice to the power supply voltage of the IC.
- While running two transistors T2 and T2 may be hot we should hold the adequate heat sink and
All resistors R4 to R6 should used many to parallel to the desired value to average Power Dissipation down.





Read more

5V Low Drop Out Regulator Low Volt by BD438

The general regulator circuit, need input voltage is higher than the output voltage. So cannot apply to the input voltage is higher just little than the need voltage. But this circuit you can have the five volt output from input voltage only six volt of the normal battery.

As circuit picture below. The load is connected with collector pin of the transistor output. Connection this way makes transistor works in a saturation. As a result the voltage drop across the collector pin and emitter pin very low (because to be the saturation voltage).
-And this current depends on a type of transistors, Which is set about 0.5 amperes, has a voltage drop is 0.2 volts. But for all circuit need plus with voltage across R6. (Current limiting resistor)
At voltage across R6 is about 0.5 volts. T3 is activated and the output current is limited there. LED-D1 is the second function is indicate working and the reference voltage. Which is set 1.5 volts to 1.6 volts at emitter pin of T1, for base current to drive it works.
Read more

9V Low Power Switching Regulator

This is the Power Switching Regulator 9V Circuit that is low current power output and It has strong point is the voltage input change from 2.4V to 10V but a constant voltage output 9 Volt. We used the RC4193 Micropower Switching Regulator is the base, easy to use and there are a few parts in circuit. The test battery point for check voltage of batter or input.
The low power switching regulator IC, number: RC4193, that that Contained in a small body of caterpillar 8-pin. It is designed for devices that work with batteries. The DC regulator power supply is built by the 11 normal parts. By has the 5 resistors, 2 capacitors, a diode, a choke coil and IC no.RC4193 and that importance the battery 2.4 volt to 9 volt : 1 set.
How it works
-This power supply has stable output voltage at 9V until battery is worn down to less than 2.4V The circuits is actual as shown below.
-The RC4193 has a reference circuit inside, is controlled by the Ic current and is define from the resistor R1 that connected externally to IC1
Read more

USB Battery Charger Circuit

This application circuit uses the MCP73853/MCP73855 linear charge management controllers for cost sensitive applications. They are specially designed for USB applications and adhere to all the USB specifications governing the USB power bus.

Read more : http://www.electronics-project-design.com/BatteryChargerCircuit.html

DC DC Converter Circuit

Get an output of 0.6V to 5.0V DC 10A from an input voltage range of 4.5V to 20V DC using Linear Technology DC DC Converter Module.

Read more : http://www.electronics-project-design.com/DC-DC-Converter-Module.html

Constructing a 12V DC Switch Mode Power Supply

Construct a 12 VDC, 120 mA switch mode supply from AC source of 85-265 VAC.

Good Links
More Circuit construct a power supply
More circuit switch mode power supply
More Switching power supply Circuit
More about 12V power supply circuit


souec: http://www.electronics-project-design.com/SwitchModePowerSupply.html

Constructing a Dual Polarity Supply

supply. With the appropriate choice of transformer and 3-terminal voltage regulator pairs you can easily build a small power supply delivering up to one amp at +/- 5V, +/- 9V, +/- 12V, +/-15V or +/-18V.

Read more : http://www.electronics-project-design.com/DualPowerSupply.html

Variable DC Supply

Another version of variable DC supply using LM317 that uses an LED to show the ON/OFF status of the supply.

Read more : http://www.electronics-project-design.com/VariableDCPowerSupply.html

Constructing a universal DC Supply

This is a basic, text-book, variable DC supply voltage regulator circuit using an LM317 from input supply of 7-20 V AC or 7-30V DC . The output voltage can be set to anywhere in the range 1.5V to 30V.

Read more : http://www.electronics-project-design.com/UniversalPowerSupply.html

Simple fixed 5V DC Power Supplies Project

This project provides the schematic and the parts list needed to construct a simple Supply from an input supply of 7-20 V AC or 7-30V DC. Two DC voltage outputs are available; 5V and variable from 5V upwards.

Related Links
More about 5v dc supply circuit
7805+Mj2955 power supply 5V 5A for digital circuit.
Simple 5V 1A Switching regulator by IC LM2575-5.0
5V 5A switching regulator for digital by LM2678

Source : http://www.electronics-project-design.com/DCPowerSupply.html

Variable 5 to 20V DC Supply

Build your own 5-20V DC power supply using National Semiconductor LM2941 low dropout voltage regulator.

Read more : http://www.electronics-project-design.com/voltageregulator.html

Variable 5 to 15V DC Supply

This is a simple DC regulated supply project using 7805 voltage regulator to obtain a variable DC voltage range from 5V to 15V.

Read more : http://www.electronics-project-design.com/RegulatedPowerSupply.html

Variable 2 to 25V DC Supply

This project uses a LM338 adjustable 3 terminal regulator to supply a current of up to 5A over a variable output voltage of 2V to 25V DC.

Related Links
More about variable dc supply circuit
More about DC Voltage Regulator Circuit
More about Shunt Regulator Circuit
More about Dual Power Supply Circuit

Source:
http://www.electronics-project-design.com/PowerSupplySchematic.html

CAPS PROVIDE VOLTAGE BOOST TO SERIES REGULATOR

CAPS PROVIDE VOLTAGE BOOST TO SERIES REGULATOR
This circuit adds some capacitors and diodes to a traditional transformer type series regulator circuit to extend the normal operating range. It can insure regulation during low line voltage conditions or it can squeeze a few more watts out of a plug-in-the-wall power adapter power supply.